n1ceguru.netlify.app

1. How To Use Smart Tv
2. How To Auto Tune A Samsung Smart Tv Remote

Select Your County. This helps store the TV services on the right channels. So BBC1 would become 1 on your TV, BBC2 would be 2, ITV = 3 and so on. It does this by reading the Logical Channel Number (LCN) information within the digital TV signal and stores the service to the correct channel. Jul 30, 2018  As with adjusting the display, there are two methods for accessing audio settings. Open the Quick Settings for audio presets. The first method is to use the Quick Settings on the home screen. Download vst plugins cho adobe audition cs6. Kitchen craze master chef cooking game download. Navigate all the way to the left, to the Settings tab, and up to.

How To Use Smart Tv

Comments

How To Auto Tune A Samsung Smart Tv Remote

• #2

  I turned off Sky yesterday - all was working fine - just wanted to save some money.
  I disconnected my Skybox and plugged the cables from the Sky dish into my Samsung TV and tried to tune in Freesat but am not getting any channels. Like I said, Sky works fine so it is not a dish / cable issue.
  The Samsung TV is model UE46F7000ST. It supports Freesat and tuning in Freesat is one of the options (along with normal satellite, aerial, cable).
  Again - freesat is built in (it is an option when I go to tune).
  Any ideas why this is not working? Many thanks!

  
  Check the f connectors weren't loosened when you swapped them over (screwed them firmly onto the coax). Can you access the manual tune option ? If so check you have a signal from the freesat home transponder
  11425.00 H DVB-S QPSK 27500 2/3 Note the frequency may not be shown as exactly 11425.
  Next check
  11426.00 V DVB-S QPSK 27500 5/6
• #3

  Another connector issue I've seen if you are a bit ham fisted with the F-Types is bending the inner pin up into the body of the plug rather than it going into the hole in the socket on the TV.
  Can an LNB be damaged if you connect and disconnect with the Sky box or TV powered up at the time?
• #4

  I turned off Sky yesterday - all was working fine - just wanted to save some money.
  I disconnected my Skybox and plugged the cables from the Sky dish into my Samsung TV and tried to tune in Freesat but am not getting any channels. Like I said, Sky works fine so it is not a dish / cable issue.
  The Samsung TV is model UE46F7000ST. It supports Freesat and tuning in Freesat is one of the options (along with normal satellite, aerial, cable).
  Again - freesat is built in (it is an option when I go to tune).
  Any ideas why this is not working? Many thanks!

  
  You could have left the skybox connected, and the card would have switched to FSFS mode, since you cancelled your subscription
• #5

  It will still cost X amount a year to run a sky box even in FSFS mode, not even recording, fyi.
• #6

  Some TV's default to the first method of FTA channels you chose so if you chose FREEVIEW it might be trying to tune into FREEVIEW Channel's .
  Have you made sure you're tuning a FREESAT tuner on the TV?
• #7

  With both satellite cables connected to the back of the TV, go to Menu, Broadcasting, Auto Tune and it should prompt you with a Postcode and then it will tune in Freesat
  Failing that do a system reset - Menu, Support.. http://www.samsung.com/ie/support/skp/faq/1051919
• #8

  Indeed, where X is the cost of electricity, nothing more.

  
  True, but a Sky box, unless put into full standby (only possible on HD boxes, holding standby button until light goes red instead of amber), only shuts down its video outputs when you shut it off.
  The receiver stays active to receive the 'keep alive' signal for the viewing card and other updates, whereas a Freesat receiver shuts down to a very minimal power consumption (basically just the IR receiver and timer) when shut down.
  There could be a quite noticeable difference in the amount of power used over 12 months.
• #9

  True, but a Sky box, unless put into full standby (only possible on HD boxes, holding standby button until light goes red instead of amber), only shuts down its video outputs when you shut it off.
  The receiver stays active to receive the 'keep alive' signal for the viewing card and other updates, whereas a Freesat receiver shuts down to a very minimal power consumption (basically just the IR receiver and timer) when shut down.
  There could be a quite noticeable difference in the amount of power used over 12 months.

  
  About £20.00 or so depending on tariff.
• #10

  Sorry - been traveling for work and will check these today.
  I did have a very hard time in getting the connectors on and was really surprised at that. So will look at that. I will also try the manual tuning trick to see if I can get a base signal.
  The TV specifically asked for my post code and as I mentioned, said FREESAT when I did the tuning. For grins, I used a normal Ariel and tuned in some FREEVIEW channels just to see if that worked.
  I know I could have left the Sky box in but did not see the point? It was one less box in the area (I also have an HTPC, router, PI, ..) so figured why not go directly to the TV as it should work.
• #11

  OK - all sorted. My connectors must not have been seated properly. They were not bent but they must not have been screwed in as tightly as they could have been. Feel like a numpty. :-)
  Thanks for all the help and happy 2017!
• #12

  Sorry - been traveling for work and will check these today.
  I did have a very hard time in getting the connectors on and was really surprised at that. So will look at that. I will also try the manual tuning trick to see if I can get a base signal.
  The TV specifically asked for my post code and as I mentioned, said FREESAT when I did the tuning. For grins, I used a normal Ariel and tuned in some FREEVIEW channels just to see if that worked.
  I know I could have left the Sky box in but did not see the point? It was one less box in the area (I also have an HTPC, router, PI, ..) so figured why not go directly to the TV as it should work.

  
  Makes sense to me, why use extra electricity if you can't record anything. Also the epg will have loads of channels you can't watch. Doesn't your TV allow recording to a usb drive, most modern smart TV's do ?
  Failure at the postcode validation stage is what you will get if the freesat home transponder is not receivable. The postcode database needs to be downloaded from the home transponder. If the connections are OK and you can't get the Horizontally polarised home transponder but can get the Vertically polarised one with much the same frequency, the lnb skew may need tweaking.
  EDIT OP posted solution while I was typing